UNITED STATES HARDWARE

STEM FAUCT PLST FOR BT DIV 4IN..

Standard or drive-in latch. Key to thumb. Fits doors 1-3/8 to 1-5/8 in thickness. 2-3/8 in setback. Bagged...

Used on front and rear entrance doors. Round drive-in latch locked from exterior by key, locked from interior by pushing handle in and turning clockwise. 2-3/8 in backset. Key included. Requires Philips head screwdriver for installation. Carded...

Imported 4 way universal entry lock. Standard or drive-in latch. Fits doors 1-3/8 to 1-5/8 in thickness. 2-3/8 in or 2-3/4 in setback. Carded...

Standard or drive-in latch. Fits doors 1-3/8 to 1-5/8 in thickness. 2-3/8 in setback. Key to thumb. Bagged...

Used in the installation of ceiling tile, mirrors and many other household fixtures. 1-1/8 in Dia. Screws included with white buttons have white heads, screws included with clear buttons have mill finish heads. Bagged...

Used in installation of ceiling tile, mirrors and many other household fixtures. 1-1/8 in Dia...

Used in installation of ceiling tile, mirrors and many other household fixtures. 1-1/8 in Dia...

Used in the installation of ceiling tile, mirrors and many other household fixtures. 1-1/8 in Dia. Screws included with white buttons have white heads, screws included with clear buttons have mill finish heads. Bagged...

Used in installation of ceiling tile, mirrors and many other household fixtures. 1-1/8 in Dia...

For bedroom or bathroom doors. 2-3/8 backset. Bagged...

For hall and closet doors where no locking is required, both knobs always free. 2-3/8 in setback. Fits doors 1-3/16 to 2 in thickness...

Drive-in latch. 2-3/8 in setback. Used on Kwikset interior lockset...

Size 1-9/16 in x 4-1/4 in. Carded...

Size 1-9/16 in x 4-1/4 in...

Size 2-3/4 in x 4-1/2 in...

Size 1-9/16 in x 4-1/4 in. Carded...

Size 1-9/16 in x 4-1/4 in...

Size 2-3/4 in x 4-1/2 in...

For stationary propane use. With drip lip vent. Gas pressure 11 in water column. 7/16 in female x 9/16 in female...

US Hardware Drain Plug, Stainless Steel, Suitable for: 1 in Dia Drain..

Fits most engines with side water inlets. Flushes away sand, silt, salt and alkali. Prevents clogging and corrosion, extending the engine life. Installs in seconds without tools...

For OMC, Johnson and Evinrude. Features ultrasonically welded acetal. 3/8 in Barb...

Brass. For 1 in Dia drains...

Pumps water level down to 3/8 in. Comes with compact 3/4 ID hose with 3-5/16 in high. For use with 12 VDC systems only. Outputs 600 gph at 0 deg rise. Will perform at reduced capacity up to 3 ft rise...

Replace ultra-flow bulb. Large alcohol compounded primer bulb for 3/8 in fuel line assemblies. Reduces flow restriction for maximum flow...

For boats up to 39.4 ft length. Die-cast Zamak with perma-plate chrome finish. Light includes one 7.5 W lamp. Base is pre-drilled with two countersunk holes for #8 screws. Size 1-3/8 in x 2-3/4 in x 2-1/2 in...

Fuel connector, male for OMC engines. Brass construction and 1/4 in NPT thread...

Molded one-piece construction of white marine vinyl. Smooth, round shape assures fewer hull abrasions. Grommets are integrally molded into each end to allow easy vertical or horizontal use...

Die-cast Zamak® with perma-plate chrome finish. Base is pre-drilled for four #8 fasteners...

Cam-action neoprene plugs. Snap shut to form a leak-proof stopper for Livewells or Baitwells...

Plastic handle with black thermoplastic body. Rated for 5 A load, 15 A inductive load. 12 VDC only. 1-3/8 in x 3/4 in...

US Hardware Two-Position Switch, 2-Wire Marine, Specifications: 12 VDC, Chrome..

All round light. Rubber storage clips hold pole when not in use. Nickel-plated brass finish washer suitable for up to #8 fastener...

Perma-plated chrome Zamak. 1 in inside eye Dia. Nut and washer included. Up to 2500 lb. pull...

Panel-mounted rocker switch for use with pump that draws 10 A or less. 1/4 in spade terminals. 6 V through 32 VDC only...

US Hardware Fuel Line Connector, Specifications: 1/4 in Barb, Brass, Chrome..

Features ultrasonically welded acetal...

Features ultrasonically welded acetal...

Features a swivel cover that protects the socket when light is stowed away. Socket is non-corrosive, plastic base extends just 3 in below deck when installed. Pre-drilled with three countersunk holes for #10 screws. 1-3/8 in hole Dia...

Die-cast Zamak with perm-plate chrome finish. 1-1/8 in inside Dia. Plated steel nuts and washers included. Made from long-lasting stainless steel 7/16 in stock. Makes an ideal ski tow hook. Maximum load 3500 lb...

Die-cast Zamak® with perma-plate chrome finish. Base is pre-drilled for four #10 fasteners...

Pre-drilled to accommodate four #6 screws. Durable chrome-plated brass ring is small enough to fit on most hatches, cabinets and drawers...

Panel-mounted rocker switch for use with pump that draws 10 A or less. 1/4 in spade terminals. 6 V through 32 VDC only...

Brass. For 1 in Dia drains...