SELKIRK

Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another...

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee...

Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield...

Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney...

Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4 in space around chimney pipe (or 2 in further than the required clearance)...

Used along the wall to provide for 2 in clearance and assure stability. Useful for suspending offsets. Required at 8 ft or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall...

Provides the support package and termination parts for a chimney that is supported by a flat ceiling and passes through an attic area and penetrates a 2/12 to 6/12 pitch roof. Just add pipe lengths and the Flat Ceiling Support Kit (FCK) has all necessary parts for complete installation. However, dep..

The Pitched Ceiling Support Kit provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and adjustable flashing (AF). Selection of the Adjustable Flashing is determined by the pitch of your roof...

For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running verticaly up the exterior wall to termination above the roof line. The thru-the-wall support kit provides all necessary parts for a complete installation with the excepti..

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Sure-Temp-Type HT Chimney (5 in, 6 in, 7 in and 8 in sizes) the round top is designed with three legs that slide down over the..

Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning...

Flashings are used to seal the opening where the chimney penetrates the roof and to divert rain and snow down from the roof and away from the chimney system.A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch r..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a locking band, to pass safely through combustible walls. An insulated tee cap is included which can be removed from bottom opening for i..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

Can be used for fixed offsets of 15 deg slope or in pairs for offsets adjustable from zero to 30 deg slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing. Required locking bands (2 packaged with each elbow kit) allow 360 deg rotation and lock the components..

Can be used for fixed offsets of 30 deg slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required locking bands (2 packaged with each elbow kit) are to be used at each joint. Each offset must be resupported. Elbows rotate 360 deg to provide the exact o..

Selkirk Drip less Smoke Stove Pipe Adapter, 430 Stainless Steel, Dimensions: 15-3/4 In L..

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection...

Contains one 18 in length of pipe, roof brackets and necessary hardware. Not for use with coal burning stoves...

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5, 6, 7 and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of the larger sizes, 10, 12 and 14 in, is 40 ft of chimney. The wall support is intended for use with the Insulated Tee a..

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4 to 6 ft...

Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another...

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee...

Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield...

Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney...