SELKIRK

FLASHING ROOF 8IN ADJ 6-12/12..

Selkirk Bird Proof Round Top..

Selkirk Roof Flashing, Aluminum/Galvanized Steel, 16 in OAL, 13-1/4 in OAW, Suitable for: 4 in Dia Pipe..

This new design gives you the flexibility of securing the 5, 6, 7 or 8 in Dia chimney with a heavy-duty band. The band allows you to slide the installed length verticaly to properly position this section in the system. Installation requirements are the same as our standard RSP. The URSA can hold 30 ..

Selkirk Flashing Kit, Rubber, Suitable for: 5 to 8 in Dia Chimney, Includes: 23-4/5 x 21-1/2 in Rubber Boot, Mounting Screws, Spacers Kit, Special Storm Collar..

Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the tee snout, using a Locking Band, to pass safely through combustible walls. An insulated tee cap is included which can be removed from bottom opening for i..

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal press..

Can be used for fixed offsets of 15 deg slope or in pairs for offsets adjustable from zero to 30 deg slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing. Required locking bands (2 packaged with each elbow kit) allow 360 deg rotation and lock the components..

Can be used for fixed offsets of 30 deg slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required Locking bands (2 packaged with each elbow kit) are to be used at each joint. Each offset must be resupported. Elbows rotate 360 deg to provide the exact o..

Selkirk Drip less Smoke Stove Pipe Adapter, 430 Stainless Steel, Dimensions: 15-3/4 In L..

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection...

Contains one 18 in length of pipe, roof brackets and necessary hardware. Not for use with coal burning stoves...

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5, 6, 7 and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of the larger sizes, 10, 12 and 14 in, is 40 ft of chimney. The wall support is intended for use with the Insulated Tee a..

Interior resupport assembly allows for two different methods of chimney resupport. The first method is used at the immediate section of chimney above the upper elbow of an offset. With the appropriate fire stop/joist shield (JS) in place, clamp the support band around chimney and attach with six-she..

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4 to 6 ft...