Plumbing Supply In NYC - Jamaica Hardware

Rubber boot inlet and outlet. Full flow design, weighted flapper valve...

Includes one universal check valve and two adapters. Made from durable ABS plastic. High-quality Nitrile-Buna N seal. Fits all 1-1/4 and 1-1/2 MPT and FPT...

Work with all pumps with a discharge size of 1-1/4 in or 1-1/2 in. For permanent or temporary use. 24 ft poly drainage tubing. Includes 1-1/4 in and 1-1/2 in adapters with rust-resistant hose clamps...

Heavy-duty flexible hose for suction or discharge. For permanent or temporary use. Includes 1-1/2 in corrugated hose, 1-1/2 in male adapter and stainless steel hose clamp. 24 ft length...

Superior Pump Sealed Lead Acid Pump Battery, Specifications: 12 V, 75 Ah, Dimensions: 10-1/4 in L x 6-1/2 in W x 9-1/2 in H..

Thermoplastic construction, continuous duty, thermally protected, split capacitor motor, will lift water up to 25 ft of vertical height, 1-1/2 discharge, 4.1 A, 10 ft cord. 3/8 in solids handling, pump is mounted to base to prevent clogging and switch malfunction. Vertical float switch, pre-plumbed ..

Length of 14 in. Turns off gas and water at the meter. Made of steel. Lifetime warranty. Carded...

For fast, clean pipe cutting, long shanked frame protects thread on cutter screw from wear. Shockproof malleable frame assured not to break or warp. Spring action cutter prevents damage to rollers. Will cut black iron pipe and hollow galvanized steel fence post. All bearing points. Rental...

Fits hex nuts and all 4, 6 and 8-tab locking nuts on strainer drain...

Infinitely adjustable head angle design for up to 1 in hex and square nuts in tight places. Shaft made of steel and jaws of powder metal. Rental...

The spring-loaded jaws and adjustable head angle design accommodates up to 1 in hex and square nuts in tight places. Extends to 17 in...

Basin Buddy universal faucet nut wrench Fits metal lock nuts, coupling nuts, PVC locknuts, most metal and plastic toilet supply nuts. Use with 1/4 in or 3/8 in ratchet drive, adapter included...

Universal design for installation and repair of kitchen and bath "P" trap DWV nuts, kitchen sink basket strainer nuts and plastic DWV nuts and wing tabs. Rental...

Fits most sizes of square and hex notes in faucet seats. 6 in x 6 in heat-treated steel...

Removes large and small faucet handles. Heat-treated, alloy steel components. One-piece cast cross bar for increased strength and durability. Notches ensure positive and equal positioning of puller arms on cross bar. Compression sleeve puller (ferrule remover) included for easy removal of 1/2 in cop..

Ideal for access to drain trap fittings on installed pedestal sinks. Can be used while the sink is in place. For drains with six, eight or 12 sided nuts...

Eliminates possibility of damage to threads, walls and external finish. Provides non-slipping grip on the inside of nipples, pipes and fittings. Can be turned in either direction. Constructed of head-treated alloy steel...

Extract broken pipe quickly and easily. Five sizes such as 1/8 in, 1/4 in, 3/8 in, 1/2 in and 3/4 in...

The Mr. Thread Cleaner™ removes debris and renews threads on hose taps. The Mr. Thread Cleaner™ works on any common household outdoor faucet. Hook up is easy with a 3/8 in socket drive and extension or wrench. The Mr. Thread Cleaner™ is made from hardened steel and plated for long lasting durability..

Protects chrome, brass and decorative fittings. Special smooth jaw design, jaw opens to 2-1/8 in. 90 deg jaw angle...

Use to easily install or remove bath tub drains, including those without crossbars, such as Kohler or American standard. Fits 1-1/2 in closet spuds. Will not scratch fine finishes. Can be turned with an adjustable wrench extension or heavy-duty screwdriver. Will also remove/install toilet seat nuts...

Crimps standard pex black copper using 10 in vise grips. Fits all common sizes including 3/8 in, 1/2 in and 3/4 in. Made from solid hardened alloy steel. Meets ASTM F1807 spec for crimping pex. Includes crimper, pouch and "go-no go" gauge...

Flares all standard sizes of soft copper, brass or aluminum tubing. Self-centering yoke of shockproof tempered malleable steel makes SAE 450 flare joints without splitting or cracking. Hardened, super smooth cone swivels freely on ball bearings. Large wing nuts permit easy, positive locking on the t..

5/8 in OD Mini Tubing Cutter roller-less design. For use in confined areas on copper, aluminum and mild steel. Zinc-plated body. One-piece knob and screw. Heat-treated alloy steel cutting wheel. Replacement cutter wheel #42525...

Painted with rollers. Cutting capacity of 1/8 to 7/8 in OD. For use in confined areas on copper, aluminum and mild steel. Large, knurled knob allows easy tightening...

Mini for cutting copper, aluminum and mild steel tubing in confined areas. Durable epoxy powder-coated finish for corrosion-resistance and durability. Large, knurled knob and rollers allow easy tightening. One-piece knob and screw means no losing pieces. Heat-treated alloy steel cutting wheel...

1-1/4 in OD enclosed-feed capacity. 1/8 to 1-1/8 in. Cuts tubing of hard or soft aluminum, brass, copper and thin wall conduit. Enclosed feed mechanism to protect threads against dirt and damage. Tubing rides freely on hardened rollers. Cuts cleanly without burrs or tubing distortion. Long-life allo..

1-1/8 in OD screw-feed tubing cutter. Traditional style heavy-duty mid-range cutter. Cuts and deburrs copper, aluminum and mild steel. Durable epoxy powder-coated finish for corrosion resistance. Heat-treated alloy steel cutting wheel. Replacement cutter wheels #42835 (Cu, Al, Brass) and #42836 (PVC..

Cuts 2 in nom pipe size or 2-1/2 in OD. One-handed operation, frees up the other hand to hold the work. Aluminum cast handles with cushion grip for comfort. Durable powder coat finish for easy clean up. Hardened stainless steel blade design with pointed edge to pierce the pipe for smooth effortless ..

Superior Tool Pipe Cutter, Maximum Pipe/Tube Diameter: 1-5/8 in, Minimum Pipe/Tube Diameter: 1 in, Pipe/Tube Material: ABS/CPVC/Nylon/PE/PEX/PVC, Cutting Type: Ratchet, Stainless Steel Blade, Epoxy Powder-Coated Blade, Cushion Grip Handle, Cast Aluminum Handle, Handle Color: Red..

Cuts PVC, CPVC, ABS, fiber pipe, wood, drywall and more. Unbreakable aluminum die-cast handle and flame hardened blade...

Will cut 1-1/4 to 10 in nominal PVC schedule 40 pipe. Features a 3 in shaft and hardened steel blade with a 1-1/4 in Dia. Used to cut drain stubs to floor lever or repair broken pipes. Includes a quick disconnect feature for use with standard 3/8 in drill...

#42215 For use with #02802 pipe cutter 2 in capacity...

Hardened steel, remove 1-1/2 in tub drains with 1/2 in ratchet drive and extension or wrench...

Bends copper, aluminum and soft thin-wall tubing. Set of four includes 1/4 in, 3/8 in, 1/2 in and 5/8 in. Bright-plated...

Quick and easy way to remove leaking compression sleeves without damaging walls. Unique armless design screws directly into compression nut for fast removal of compression sleeve or ferrule. For 1/2 in (5/8 in actual OD) compression fittings only...

Ideal for access to drain trap fittings on installed pedestal sinks. Can be used while the sink is in place. For drains with six, eight or 12 sided nuts...

..

..

..

..

..

ADAPTER CPVC FIP X CPVC 1/2..